Weber.therm 403

adhesive compound for bonding polystyrene foam EPS panels to masonry, concrete and similar mineral surfaces. For use in lightweight facade insulation systems such as weber MW F010. Can be used for smoothing mineral substrates and for filling potholes. It is recommended to use weber.therm 410 when bonding extruded polystyrene foam.

  • Waterproof, low water absorption
  • Frost-resistant, water vapour permeable

  • Excellent adhesion, elastic, homogeneous

  • Can be used inside and outside buildings

  • Easy and quick to apply

Weber.therm 405

a bonding compound for bonding mineral wool and polystyrene to masonry, concrete and similar mineral surfaces. Dense and smooth surfaces (e.g. extruded polystyrene) must be sanded. For use in lightweight facade insulation systems such as weber MW F030. Can be used for levelling mineral substrates and for filling potholes.

  • Waterproof, low water absorption
  • Frost-resistant, water vapour permeable

  • Excellent adhesion, elastic, homogeneous

  • Can be used inside and outside buildings

  • Easy and quick to apply

Weber.therm 410

a bonding and reinforcing compound for bonding and reinforcing mineral wool and polystyrene on expanded clay concrete, stone, concrete, ceramic and silicate bricks, aerated concrete masonry, plasters and other mineral surfaces. For use in lightweight facade insulation systems such as weber MW F030 and weber MW F010. Can be used for smoothing mineral substrates and for filling potholes. When using extruded polystyrene, the surface must be sanded

  • Reinforced with polymer fiber

  • Waterproof

  • Low water absorption

  • Resistant to frost

  • Water vapour permeable

  • Excellent adhesion, elastic, homogeneous

  • Can be used inside and outside buildings

  • Easy and quick to apply

Weber HobbyConcrete

Handicrafts, crafts or art and castings. E.g.: concrete pots, candleholders, decorative interior elements, garden and craft decorations

  • Easy to use, just add water

  • Suitable for the production of many fine concrete products

  • Versatile, consistency can be varied by adjusting the amount of water

  • For interior and exterior

  • Safe and durable

Weber S 06

For the repair and smoothing of concrete surfaces (walls, ceilings, floors) inside and outside, and for the repair of defects after concrete work.

  • Mortar plastic

  • Good adhesion to the substrate

  • Frost-resistant

  • Moisture resistant

  • Low shrinkage on curing

  • Seals well

  • Complies with Class CT-C20-F4-B0,2 according to EN 13813 Annex ZA

Weber S 30

Used for repairing large defects after concrete works. For levelling concrete floors, concrete sidewalks, joints in slabs, repairing defects in concrete structures, plastering concrete plinths inside and outside the premises.

  • Used to repair large defects after concreting.

  • Suitable for exterior use.

  • Highly resistant to compression - 20-25 MPa.

  • Volume ratios: air - approx. 10-12%, moisture - approx. 2 kg/m³.

  • Conforms to Class CT-C25-F5-B0,2 according to EN 13813 Annex ZA.

Weber S 100

Weber S-100 dry concrete mix is designed for general concrete construction work. Aggregate fraction up to 10 mm. Supplied as a dry mix in bags of 25 kg and 1000 kg. Mixed with water, the concrete mix is ready for use. Average compressive strength 25 MPa

  • Weber S-100 is designed for large volumes of concrete or monolith casting work on non-load bearing structures

  • Recommended layer thickness not less than 30 mm

  • Weber S-100 is suitable for foundations, floors, lintels, beams, stairs, monolithic elements

Weber.floor BASE 10

Weber.floor BASE 10 is intended for the production of levelling cement floors, bases, boiler rooms, basements, individual garages, apartments and the exterior of public buildings, such as terraces, and balconies. Recommended for use on concrete, ceramic, stone, and cast cement bases. The mixture is used as a base for thick carpets, PVC, cork coverings, ceramic and stone tiles, parquet, panels, etc. Suitable for use with all adhesives used for glueing the mentioned coatings. Can be used for "floating" floors, on sound and thermal insulation, or in-floor heating systems. Suitable for filling holes in concrete

  • Layer thickness: 10-80 mm, for hand levelling or flooded applications

  • High strength, reduced shrinkage

  • For use inside and outside buildings

  • Frost-resistant, homogeneous, vapour permeable

  • Easy and quick to process

  • Casein-free, environmentally friendly

  • Complies with Class CT-C-F4 according to EN 13813 Annex ZA.

Kiilto KeraPro

A new generation of fast-drying waterproofing membrane. Easy to apply or spray. The thickness of the installed waterproofing membrane coating can be measured with an ultrasonic gauge without damaging the coating. CE marked, ETA approved, single component. Reinforced with microfibre

  • very fast Drying time: roller application approx. 1+2 hrs, spray application approx. 1 hr.

  • gel-like, easy to apply

  • yield 0,75 l/m² = 1 kg/m²

  • suitable for insulating air vents

Kiilto Keramix Nesteosa A liquid + Jauheosa X powder

A very fast-drying, two-component waterproofing membrane for wet rooms, balconies, and terraces before tiling. Also suitable for external use and unheated interior spaces. Also suitable for air and radon leakage insulation.

  • cementitious, two-component

  • paste consistency ideal for substrate levelling and insulation of inlets

  • frost tested

  • tested for air gap insulation (Vahanen)

  • drying time: 1st coat in 1 hour, 2nd coat in 1,5 hours

Kerastop

Insulating walls against moisture before tiling. Suitable for unpainted walls in wet rooms and for walls in utility rooms and kitchens. VTT product certificate C51/99

Kiilto Nurkkavahvike tape

For insulating corners, joints and material joints. For use with Kiilto waterproofing membranes

Kiilto Kaivolaippa

Self-adhesive butyl reinforcement sheet for floor drains. For use with Kiilto waterproofing systems

Fibergum

Kiilto Fibergum is a ready-to-use, fibre-reinforced, waterproof membrane for use under wall and floor tiles in baths, saunas and similar wet areas. Not suitable for areas permanently under water (e.g. swimming pools) and where temperatures exceed 60 °C

Kiilto Butyylinauha

Insulation and reinforcement of corners and corner sections when using Kiilto waterproofing systems. Also suitable for protection against weather and accidental leakage using Kiilto Keramix and KeraPro waterproofing systems. Ideal for external use.

Kiilto Sisänurkkavahvike

Pre-formed elastic corner reinforcements shall be used with rolled waterproof membranes. Must be used as part of the „KeraSafe“

waterproof system.

Kiilto Vahvikekangas

Kiilto Vahvikekang reinforcement material can be used to cover the entire waterproofed area between the layers of Kiilto's single component waterproofing membrane. The reinforcement material is also suitable for insulating corners, joints, edges and material joints. For use with Kiilto waterproofing systems single component waterproofing membranes.

Kiilto Ulkonurkkavahvike

Pre-formed elastic corner reinforcements shall be used with rolled waterproof membranes.
Must be used as part of the „KeraSafe“

waterproof system.

Entry reinforcement sheet

Pre-fabricated reinforcement sheets for pipe inlets Inlet reinforcement sheets are available in diameters of 10-16 mm, 18-34 mm (e.g. Ø 32 mm floor drain), 34-50 mm (e.g. wall socket), 55-75 mm (e.g. Ø 75 mm floor drain) and 100-140 mm (e.g. toilet inlet).

Kiilto M1000 ECO

Universal adhesive for the installation of vinyl flooring and tiles, linoleum, rubber and textile flooring and PVC-free flooring. Also suitable for installation of Kiilto KeraSafe foil. 2-ethyl hexanol free. Free of APEO compounds, phthalates and other plasticisers. Also suitable for bathroom applications.

  • Multi-purpose adhesive for floor and wall coverings

  • water-based

  • free of 2-ethyl hexanol contamination, free of APEO mixtures, phthalates and other plasticisers

  • suitable for most floor coverings